Doppelschnecken-Co-Rotat ICMA SAN GIORGIO MCM/60V – 40D

Kunststoffverarbeitungsmaschinen / Extruder

weitere Fotos anfordern

Exapro S.A.S
[ Händlerprofil ]

4 place Marc Leclerc
49400 Saumur
Frankreich

RESALE Anbieter seit 2023

Maschinenliste (4981)

Anfrage

merken

Anfrage sendenAnfragen

Eintrags-Nr.: 162912059	Anzahl: 1	Datum: 26.04.2024
Baujahr: 2012	Standort: Frankreich

Preis: [netto]	383.000 EUR
Hersteller:	Icma San Giorgio
Modell:	MCM/60V – 40D
Maschinentyp:	Doppelschnecken-Co-Rotat
Beschreibung:	Doppelschnecken-Co-Rotat Icma San Giorgio MCM/60V – 40D Gebrauchtmaschine Icma San Giorgio MCM/60V – 40D twin screw co-rotating extruder Mod. MCM/60V-40 D and down stream equipment High performances, intermeshing screw type for self cleaning characteristics. Screws Ø 60 mm Nominal L/D ratio 1:40 Max screw speed 300 rpm Barrel Modular design made up by 10 square-barrel sectors, each one 4 D long Barrel sectors made of LK3 nitrided steel Built-in water cooling circuit, simple construction and easy to maintain High efficiency heating system by cartridge heater Broached shaft made in special alloy brake/yield/torsion resistant Modular design Screw elements made of K 110 wear resistant steel Gear box Torque per screw shaft Nm. 1050 per each shaft Gear-ratio 4.28 : 1 Min. bearing lifetime at max. speed and motor power 20,000 working hours @ 160 bar Main A.C. motor Power applied to gearbox shafts KW 66 Speed rpm 1285 Water cooling unit for extrusion barrel -To supply cooling water in to each barrel sector Including circulating pump -Water/water heat-exchanger with expansion tank Interconnecting piping. GRAVIMETRIC FEEDER FOR POLYMER IN PELLET FORM Loss in weight gravimetric metering unit with max capacity up to 35% of total line out put Screw type feeder with high resolu -Lion digital loading cell Re-filling hopper 50 lLevel detecting sensor Pneumatic discharge valve GRAVIMETRIC FEEDER FOR GROUND SCRAP Loss in weight gravimetric metering unit with max capacity up to 25% of total line out put Screw type feeder with high resolution digital loading cell Re-filling hopper 23 l Level detecting sensor Pneumatic discharge valve GRAVIMETRIC FEEDER FOR ADDITIVE IN PELLET FORM Loss in weight gravimetric metering unit with max capacity up to 10% of total line out put Screw type feeder with high resolution digital loading cell Re-filling hopper 23 l -Level detecting sensor -Pneumatic discharge valve GRAVIMETRIC FEEDER FOR WOOD FLOUR Loss in weight gravimetric metering unit with max capacity up to 80% of total line out put Screw type feeder with high resolution digital loading cell Special execution for hard flowing powder Re-filling hopper 200 l special execution for hard flowing powder Vibrating Level detecting sensor- Pneumatic discharge valve CONTROL PANEL For up to 4 gravimetric unit control User friendly graphic display with touch screen. Recipes management software Profiles extrusion die Connection piece to the gear pump Build in stainless steel Heating by electrical heaters # 5 thermo-regulated zones included in the main cabinet Profiles calibrating group Dry and wet system Calibrator openable by pneumatic actuators Made of stainless steel Under vacuum cooling tanks Made of 3 section 2 m long 2 section with vacuum circuit 1 section for cooling only Made of Aluminium and Plexiglas Cooling system full water” MAIN CONTROL CABINET PLC system based, to control all driving sequences Operator Interface with touch-screen colour monitor # 18 temperature control zones (2 spares zones for dies) Zones thermoregulation integrated in the PLC Air conditioning system Build as per CE standards Protection level: IP 54 FLAT-TRACK TYPE HAUL-OFF TPM 1100/2C For max profile width 150 mm Steel frame and aluminium track holding structure Flat track made of special wear resistant synthetic rubber 1,5 Kw driving motor for each track Pneumatic cylinders for upper track opening/closing, max. stroke 160mm Safety devices CROSS CUTTING UNIT For max profile width 150 mm Steel structure Widia blade Ø 400 mm Pneumatic cylinder for blade down-stroke 1,5 kw driving motor Safety devices Dust collecting system COLLECTING BENCH FOR CUT PROFILES Steel structure with aluminium sliding plate Plate dimensions: 500 x 6000 mm Side ejection system pneumatically actuated to move the profiles in the to the collecting inclined plane Verkäufer Angebot Nr. resale P00426001
Positionsnummer des Verkäufers:	P00426001

Diese Maschine auf Facebook

Diese Maschine als verkauft

verwandte Suchbegriffe

Doppelschnecken Extruder + Fave giorgio axel mischer und vakuummischer + San roco cnc bohrwerke