GF

Used DC GF 3-in-1 filling line, sparking water 6000 BPH, Year 2013Technical Specifications & Performance DataThis used bottling line is configured for PET bottle production and beverage filling, combining a linear blow molding machine, high-pressure compressed-air equipment, an integrated rinsing, filling and capping monoblock, labeling, coding, saturation and shrink-wrapping equipment. The line is designed for industrial packaging of carbonated, oxygenated and non-carbonated beverages.Blow molding capacity: 1,000–2,000 bphFilling monoblock capacity: 4,000–6,000 bph at 0.33LSupported bottle formats: 0.33L, 0.5L and 1.5LContainer material: PET bottles with PCO neck finishComplete line footprint: approximately 11 m × 6 mBlow molder configuration: linear, 2 cavities, 20–50 g preformsFilling monoblock: 18 rinsing stations, 18 filling valves and 6 capping headsAdvanced Automation & Control SystemsThe line includes Mitsubishi PLC control for the filling and handling process. The filling monoblock uses an electronic filling system and operates with clockwise bottle movement. Safety functions are fitted on the blow molding machine, compressor and filling monoblock, while safety covers are included for the complete line.Electrical supply for the blow molder and compressor: 400 V, 15 kW, 50 HzElectrical supply for the filling monoblock: 400 V, 3.5 kW, 50 HzElectronic non-isobaric filling systemPCO 32 and PCO 28 cap compatibilityIntegrated HS-Datu dating unit for production codingProduction Line Integration CapabilitiesThis complete PET bottling line follows a practical process flow from bottle forming through filling, labeling and secondary packaging. The linear blower is supplied with a preform feeder, preform tipper, 30 bar three-stage compressor, cooling dryer and air filter. Downstream equipment includes a self-adhesive labeling machine, vacuum saturator, conveyor system and automatic shrink film wrapper.Machine typeManufacturer / modelYearBlow Molding MachineECENG MACHINERY Co. Ltd.2010CompressorChina2010Filling MonoblockDC GF 3-in-12013SaturatorVacuum saturatorLabeling MachineSelf-adhesive labelerShrink WrapperAutomatic shrink film wrapperVarious EquipmentConveyor systemPrinterHS-Datu dating unitThe automatic shrink wrapper provides a stated output range of 1,000–3,000 bph. The vacuum saturator is rated at 1,000 L/h and supports beverage preparation for carbonated product applications.Machine Condition & Maintenance HistoryThe filling triblock is reported in production and has recorded operating time of 300 hours. The blow molding machine and high-pressure compressor are operational. The blower itself was tested and confirmed working; the complete line was never installed in its original small workshop configuration. Manuals are available for the filling monoblock, while maintenance documentation is not included for the listed equipment.Operational Performance & VersatilityThe line is suitable for PET beverage production using 0.33L, 0.5L and 1.5L formats. Its PCO bottle handling configuration supports PCO Normal preforms, with Shorti preforms also accepted by the blower. The filling monoblock integrates rinsing, electronic filling and PCO capping in a compact production unit. The line is configured for sparkling water and supports carbonated, oxygenated and non-carbonated filling applications.Installation Requirements & Site PreparationInstallation requires an area corresponding to the stated approximate 11 m × 6 m line footprint, with sufficient access around the equipment for operation, service and container handling. The blower measures 4 m × 2 m × 2.5 m, while the filling monoblock measures 2.6 m × 2.4 m × 2.1 m. A 400 V, 50 Hz electrical supply is required. The PET blowing section is supported by the included 30 bar compressed-air system, cooling dryer and air filtration equipment.Safety Standards & Compliance CertificationSafety functions are listed for the principal production machines, and the complete line includes safety covers. These protections support controlled operation around moving bottle-handling, filling, capping and packaging sections. During installation and commissioning, guards, emergency stops, electrical protection and interlocked access points should be verified as part of the site safety assessment.